Kangoo Models

Name: Front Arm Front BushProduct Notes: Weight: 319Fitting Instructions

Name: Front Arm Front BushProduct Notes: Weight: 319Fitting Instructions

Name: Front Arm Front Bush Camber AdjustableProduct Notes: Weight: 448Fitting Instructions

Name: Front Arm Front Bush Camber AdjustableProduct Notes: Weight: 448Fitting Instructions

Name: Front Arm Rear BushProduct Notes: Weight: 781Fitting Instructions

Name: Front Arm Rear BushProduct Notes: Weight: 781Fitting Instructions

Name: Front Arm Rear Bush Caster Offset Product Notes: PFF60-902G provides a fixed 4mm offset to provide +/- 0.5 caster offset for improved steering feel. Additional caster will also create additional negative camber on turn giving improved tyre contact with the road under heavy cornering. For a non-offset version of this bush please use PFF60-902. Weight: 781Fitting Instructions

Name: Front Arm Rear Bush Caster OffsetProduct Notes: PFF60-902G provides a fixed 4mm offset to provide +/- 0.5 caster offset for improved steering feel. Additional caster will also create additional negative camber on turn giving improved tyre contact with the road under heavy cornering. For a non-offset version of this bush please use PFF60-902. Weight: 781Fitting Instructions

Name: Front Upper Right Engine Mount Insert Product Notes: For Clio 172/182 Sport and Twingo RS133 models only. This polyurethane insert fits into and fills voids in the original rubber bush. It is designed to limit movement of the engine to provide additional stability under acceleration. Weight: 240Fitting Instructions

Name: Front Upper Right Engine Mount Insert Product Notes: For Clio 172/182 Sport and Twingo RS133 models only. This polyurethane insert fits into and fills voids in the original rubber bush. It is designed to limit movement of the engine to provide additional stability under acceleration. Weight: 240Fitting Instructions

Name: Gearbox Mounting Bush InsertProduct Notes: PFF60-1421 Gearbox Mounting Bush Insert is a two-part kit that acts to stiffen the upper and lower voiding of the OE mount, helping to restore a level of responsiveness expected from a hot hatch. Made using our Yellow 70A durometer material, it provides the perfect balance between compliance and stiffness, giving control and precision without compromising comfort. A small increase in NVH, usually at idle should be expected when stiffening the mounting between the engine/transmission and chassis. The harder the material used, the greater the NVH transmitted. For total drivetrain control, this new insert is the perfect accompaniment to PFF60-1420 Upper Engine Mount Insert and PFF60-1422 Lower Torque Mount Weight: 124Fitting Instructions

Name: Gearbox Mounting Bush InsertProduct Notes: Made using our Black 95A durometer material, PFF60-1421BLK Gearbox Mounting Bush Insert is a two-part kit that acts to stiffen the upper and lower voiding of the OE mount, helping to restore a level of responsiveness expected from a hot hatch. A small increase in NVH, usually at idle should be expected when stiffening the mounting between the engine/transmission and chassis. The harder the material used, the greater the NVH transmitted. For total drivetrain control, this new insert is the perfect accompaniment to PFF60-1420BLK Upper Engine Mount Insert and PFF60-1422BLK Lower Torque Mount. Weight: 124Fitting Instructions

Name: Lower Engine Mount InsertProduct Notes: This is an insert that fits into and fills voids in the original rubber bush in lower engine mount. Fits Clio III ,Megane II, Kangoo II and Scenic II 1.5L Diesel models. Also fits 1.6L Petrol Clio III and Kangoo II. Weight: 156

Name: Lower Engine Mount InsertProduct Notes: This is an insert that fits into and fills voids in the original rubber bush in lower engine mount. Fits Clio III ,Megane II, Kangoo II and Scenic II 1.5L Diesel models. Also fits 1.6L Petrol Clio III and Kangoo II. Weight: 156

Name: PowerAlign Camber Bolt Kit (14mm) Product Notes: Our PowerAlign camber bolts replace the original upper bolt on suspension struts with a two-bolt fixing to the knuckle, one positioned above the other, allowing up to +/- 1.75 degrees of adjustment. This kit contains 2 camber bolts, tab washers and nuts. Why not add our Magnetic Camber Gauge to your tool kit so that you can make pit garage adjustments to your suspension using PowerAlign Camber Bolts? Bush Size: M14 x 70mm Weight: 261 Fitting Instructions

Name: PowerAlign Wheel Mounting Guide PinProduct Notes: Available singularly to suit a specific vehicle or as a handy 4-piece workshop kit, our new PowerAlign Wheel Mounting Guide Pins are designed to allow the safer mounting and easy alignment of heavy alloy wheels on most common cars to use lug bolts. The individual pins come supplied in a reusable twist tube and the 4-piece workshop kit is supplied with a steel storage case for pride of place in your toolbox.Simply thread the appropriate pin size into one of the bolt holes on the wheel hub. The wheel can then be lifted and placed on the guide pin, and easily slid into place on the hub; keeping the bolt holes aligned for other bolts to be inserted and tightened.This reduces the awkward and back-straining process of holding the wheel in place with one hand whilst lining up and threading in the first bolt; thus, reducing the risk, hassle, and strain of mounting wheels.Proven using simulated and real-world testing, the new mounting pins usehigh-strength CNC-machined AISI 303 Stainless Steel, some 50% stronger than plated mild steel, to ensure durability and resilience in a workshop environment, and are supplied with colour-coded 3D-printedprotective sleeves for ease of identificationandanodised 2011-T6 aluminium caps to absorb knocks and prevent damage to the wheel, unlike others on the market.Please clickhereto view all sizes available and fora wider-reaching application list in the form of anew user-friendly drop-down search function. Weight: 97

Name: SMI Steering Rack Mount KitProduct Notes: These mounts fit SMI Steering Racks only (not TRW racks) Weight: 66

Name: SMI Steering Rack Mount KitProduct Notes: These mounts fit SMI Steering Racks only (not TRW racks) Weight: 66

Name: Upper Right Engine Mounting BushProduct Notes: This part replaces the original bush in bracket to fit 1.5 and 2.0L diesel models. PFF60-522 is designed to allow a controlled amount of engine movement through voids in the material. The kit includes a polyurethane insert that is designed to further reduce engine movement, perfect for track days or vehicles running increased power. Weight: 310Fitting Instructions

Name: Upper Right Engine Mounting BushProduct Notes: This part replaces the original bush in bracket to fit 1.5 and 2.0L diesel models. PFF60-522 is designed to allow a controlled amount of engine movement through voids in the material. The kit includes a polyurethane insert that is designed to further reduce engine movement, perfect for track days or vehicles running increased power. Weight: 310Fitting Instructions

Name: Upper Right Engine Mounting Bush InsertProduct Notes: This is an insert that fits into and fills voids in original bush in bracket to fit 1.5 and 2.0L diesel models. Weight: 171Fitting Instructions

Name: Upper Right Engine Mounting Bush InsertProduct Notes: This is an insert that fits into and fills voids in original bush in bracket to fit 1.5 and 2.0L diesel models. Weight: 171Fitting Instructions