Citigo (2011 -)

Name: Exhaust MountProduct Notes: Bush Size: 70mm x 35mm x 11.7mmWeight: 92Fitting Instructions

Name: Front Anti Roll Bar Bush 18mmProduct Notes: Please check anti-roll bar diameter before ordering. Bush Size: 18mmWeight: 73

Name: Front Anti Roll Bar Bush 18mmProduct Notes: Please check anti-roll bar diameter before ordering. Bush Size: 18mmWeight: 73

Name: Front Arm Rear BushProduct Notes: For the Skodia Fabia 5J, this bush only fits models with these chassis numbers: F5J 8A502 657 Onward, F5J 8B503 032 Onward, F5J 8K450 961 Onward, F5J 83172 974 Onward. Weight: 780Fitting Instructions

Name: Front Arm Rear BushProduct Notes: For the Skodia Fabia 5J, this bush only fits models with these chassis numbers: F5J 8A502 657 Onward, F5J 8B503 032 Onward, F5J 8K450 961 Onward, F5J 83172 974 Onward. Weight: 780Fitting Instructions

Name: Front Strut Top Mount BushProduct Notes: Weight: 618Fitting Instructions

Name: Front Strut Top Mount BushProduct Notes: Weight: 618Fitting Instructions

Name: Front Strut Top Mount BushProduct Notes: Weight: 618Fitting Instructions

Name: Front Strut Top Mount Bush -10mmProduct Notes: This part has been designed to reduce the ride height by 10mm when fitted as it allows the strut to sit higher into the body of the top mount. It is supplied with a new top cap spacer made using our 95A durometer material, meaning no more modifying of original parts. For standard ride height top mounts, please use PFF85-430. Bush Size: -10mmWeight: 591Fitting Instructions

Name: Front Strut Top Mount Bush -10mmProduct Notes: This part has been designed to reduce the ride height by 10mm when fitted as it allows the strut to sit higher into the body of the top mount. It is supplied with a new top cap spacer made using our 95A durometer material, meaning no more modifying of original parts. For standard ride height top mounts, please use PFF85-430BLK. Bush Size: -10mmWeight: 591Fitting Instructions

Name: Front Strut Top Mount Bush -10mmProduct Notes: This part has been designed to reduce the ride height by 10mm when fitted as it allows the strut to sit higher into the body of the top mount. It is supplied with a new top cap spacer made using our 95A durometer material, meaning no more modifying of original parts. For standard ride height top mounts, please use PFF85-430H. Bush Size: -10mmWeight: 591Fitting Instructions

Name: Front Strut Top Mount Bush WasherProduct Notes: PFF85-431W Front Strut Top Spacer (as normally supplied with PFF85-431 and now available separately) is a simple and cost-effective interim solution that fits and works with the OE Strut Top Cap to fill the gap and prevents binding up on the PU Spacer as the suspension turns. Fitting couldnt be easier either. Simply remove the existing Strut Top Cap from the car, separate the rubber ring from it, press the Cap into our Spacer and then refit it! NB; fitting this part is only recommended if the installed Top Mount is in good condition and there is a gap of at least 12mm between the top cap and body. If the OE mount has collapsed, you will need to replace the entire mount with PFF85-430 or PFF85-431. Bush Size: 18mmWeight: 112

Name: Front Wishbone Front Bush 30mmProduct Notes: If fitting on Audi TT MK1, S3 and A3 MK1 and Seat Leon & Cupra MK1 it fits earlier models with a 30mm diameter. It fits both the pressed and cast arms on the Leon & Cupra MK1 and A3 MK1 2WD. Please check original bush size. Later cars may use a larger 45mm bush PFF3-501. For an on-car camber adjustable version of this bush please use PFF85-201G. Bush Size: 30mmWeight: 263

Name: Front Wishbone Front Bush 30mmProduct Notes: If fitting on Audi TT MK1, S3 and A3 MK1 and Seat Leon & Cupra MK1 it fits earlier models with a 30mm diameter. It fits both the pressed and cast arms on the Leon & Cupra MK1 and A3 MK1 2WD. Please check original bush size. Later cars may use a larger 45mm bush PFF3-501. For an on-car camber adjustable version of this bush please use PFF85-201G. Bush Size: 30mmWeight: 263

Name: Front Wishbone Front Bush 30mmProduct Notes: If fitting on Audi TT MK1, S3 and A3 MK1 and Seat Leon & Cupra MK1 it fits earlier models with a 30mm diameter. It fits both the pressed and cast arms on the Leon & Cupra MK1 and A3 MK1 2WD. Please check original bush size. Later cars may use a larger 45mm bush PFF3-501. For an on-car camber adjustable version of this bush please use PFF85-201GBLK. Bush Size: 30mmWeight: 263

Name: Front Wishbone Front Bush 30mm Camber Adjustable Product Notes: PFF85-201G gives +/- 0.5 degrees of camber adjustment. If fitting on Audi TT MK1, S3, and A3 MK1 and Seat Leon & Cupra MK1 it fits earlier models with a 30mm diameter. It fits both the pressed and cast arms on the Leon & Cupra MK1 and A3 MK1 2WD. Please check the original bush size. Later cars may use a larger (non-adjustable) 45mm bush PFF3-501. PFF85-201G bush features a CNC machined Stainless Steel sleeve with an offset bore that can be rotated using our bespoke tooling (supplied), giving +/- 0.5 degrees of on-car camber adjustment. For a non-offset version of this bush please use PFF85-201.Knurled end faces prevent sleeve rotation to retain suspension geometry.PFF85-201GBLK boosts stiffness over the original part by 15%. Bush Size: 30mmWeight: 355Fitting Instructions

Name: Lower Torque Mount Large Bush (Fast Road)Product Notes: PFF85-1923 is a complete replacement bush, only fits 2015-on 1.0 MPI and 1.0 TSI and GTI models with the post-facelift mount (see below), check which mount is fitted before ordering. For an insert only use PFF85-1922. Weight: 596Fitting Instructions

Name: Lower Torque Mount Large Bush (Motorsport)Product Notes: PFF85-1923 is a complete replacement bush, only fits 2015-on 1.0 MPI and 1.0 TSI and GTI models with the post-facelift mount (see below), check which mount is fitted before ordering. For an insert only use PFF85-1922. Weight: 596Fitting Instructions

Name: Lower Torque Mount Large Bush (Tuned/Track)Product Notes: PFF85-1923 is a complete replacement bush, only fits 2015-on 1.0 MPI and 1.0 TSI and GTI models with the post-facelift mount (see below), check which mount is fitted before ordering. For an insert only use PFF85-1922. Weight: 596Fitting Instructions

Name: Lower Torque Mount Large Bush Insert (Motorsport)Product Notes: Fitting this new insert reduces engine movement caused by the torque reaction of the engine during acceleration and deceleration. Gains can be seen in power transfer to the road along with less stress on the exhaust downpipe, hoses, and wiring. A small increase in NVH usually at idle should be expected when fitting an engine/transmission mount insert because you are effectively removing the original voiding and stiffening the mount between the engine/transmission and chassis. The performance benefits felt by fitting an uprated mount or insert come from blocking this voiding up, thus restricting engine movement. PFF85-1920 only fits 1.0 MPI and electric models with the pre-facelift mount (see below), check which mount is fitted before ordering Weight: 61Fitting Instructions

Name: Lower Torque Mount Large Bush Insert (Motorsport)Product Notes: Fitting this new insert reduces engine movement caused by the torque reaction of the engine during acceleration and deceleration. Gains can be seen in power transfer to the road along with less stress on the exhaust downpipe, hoses, and wiring. A small increase in NVH usually at idle should be expected when fitting an engine/transmission mount insert because you are effectively removing the original voiding and stiffening the mount between the engine/transmission and chassis. The performance benefits felt by fitting an uprated mount or insert come from blocking this voiding up, thus restricting engine movement. PFF85-1922 only fits 2015-on 1.0 MPI and 1.0 TSI and GTI models with the post-facelift mount (see below), check which mount is fitted before ordering. For a complete replacement bush use PFF85-1923. Weight: 60Fitting Instructions

Name: Lower Torque Mount Large Bush Insert (Standard)Product Notes: Fitting this new insert reduces engine movement caused by the torque reaction of the engine during acceleration and deceleration. Gains can be seen in power transfer to the road along with less stress on the exhaust downpipe, hoses, and wiring. A small increase in NVH usually at idle should be expected when fitting an engine/transmission mount insert because you are effectively removing the original voiding and stiffening the mount between the engine/transmission and chassis. The performance benefits felt by fitting an uprated mount or insert come from blocking this voiding up, thus restricting engine movement. PFF85-1920 only fits 1.0 MPI and electric models with the pre-facelift mount (see below), check which mount is fitted before ordering Weight: 61Fitting Instructions

Name: Lower Torque Mount Large Bush Insert (Standard)Product Notes: Fitting this new insert reduces engine movement caused by the torque reaction of the engine during acceleration and deceleration. Gains can be seen in power transfer to the road along with less stress on the exhaust downpipe, hoses, and wiring. A small increase in NVH usually at idle should be expected when fitting an engine/transmission mount insert because you are effectively removing the original voiding and stiffening the mount between the engine/transmission and chassis. The performance benefits felt by fitting an uprated mount or insert come from blocking this voiding up, thus restricting engine movement. PFF85-1922 only fits 2015-on 1.0 MPI and 1.0 TSI and GTI models with the post-facelift mount (see below), check which mount is fitted before ordering. For a complete replacement bush use PFF85-1923. Weight: 60Fitting Instructions

Name: Lower Torque Mount Large Bush Insert (Tuned/Track)Product Notes: Fitting this new insert reduces engine movement caused by the torque reaction of the engine during acceleration and deceleration. Gains can be seen in power transfer to the road along with less stress on the exhaust downpipe, hoses, and wiring. A small increase in NVH usually at idle should be expected when fitting an engine/transmission mount insert because you are effectively removing the original voiding and stiffening the mount between the engine/transmission and chassis. The performance benefits felt by fitting an uprated mount or insert come from blocking this voiding up, thus restricting engine movement. PFF85-1920 only fits 1.0 MPI and electric models with the pre-facelift mount (see below), check which mount is fitted before ordering Weight: 61Fitting Instructions

Name: Lower Torque Mount Large Bush Insert (Tuned/Track)Product Notes: Fitting this new insert reduces engine movement caused by the torque reaction of the engine during acceleration and deceleration. Gains can be seen in power transfer to the road along with less stress on the exhaust downpipe, hoses, and wiring. A small increase in NVH usually at idle should be expected when fitting an engine/transmission mount insert because you are effectively removing the original voiding and stiffening the mount between the engine/transmission and chassis. The performance benefits felt by fitting an uprated mount or insert come from blocking this voiding up, thus restricting engine movement. PFF85-1922 only fits 2015-on 1.0 MPI and 1.0 TSI and GTI models with the post-facelift mount (see below), check which mount is fitted before ordering. For a complete replacement bush use PFF85-1923. Weight: 60Fitting Instructions

Name: PowerAlign Wheel Mounting Guide PinProduct Notes: Available singularly to suit a specific vehicle or as a handy 4-piece workshop kit, our new PowerAlign Wheel Mounting Guide Pins are designed to allow the safer mounting and easy alignment of heavy alloy wheels on most common cars to use lug bolts. The individual pins come supplied in a reusable twist tube and the 4-piece workshop kit is supplied with a steel storage case for pride of place in your toolbox.Simply thread the appropriate pin size into one of the bolt holes on the wheel hub. The wheel can then be lifted and placed on the guide pin, and easily slid into place on the hub; keeping the bolt holes aligned for other bolts to be inserted and tightened.This reduces the awkward and back-straining process of holding the wheel in place with one hand whilst lining up and threading in the first bolt; thus, reducing the risk, hassle, and strain of mounting wheels.Proven using simulated and real-world testing, the new mounting pins usehigh-strength CNC-machined AISI 303 Stainless Steel, some 50% stronger than plated mild steel, to ensure durability and resilience in a workshop environment, and are supplied with colour-coded 3D-printedprotective sleeves for ease of identificationandanodised 2011-T6 aluminium caps to absorb knocks and prevent damage to the wheel, unlike others on the market.Please clickhereto view all sizes available and fora wider-reaching application list in the form of anew user-friendly drop-down search function. Weight: 97

Name: Powerflex Handling PackProduct Notes: Fits all turbocharged models, and all post-2016 VW Up! Included within this pack are the following parts:PFF85-201Front Arm Front BushPFF85-1202Front Arm Rear BushPFR85-1910Rear Beam Mounting BushPFF85-1922Lower Engine Mount InsertThis Handling Pack contains a selection of parts from a complete vehicle listing, clickhereto see more parts available. Weight: 1900

Name: Rear Beam Mounting BushProduct Notes: Weight: 772Fitting Instructions

Name: Rear Beam Mounting BushProduct Notes: Weight: 772Fitting Instructions